Purchase PP80006: 800 GPH High Lift Pump, Waterfalls/Ponds/Vertical Hydroponics/Aquaponics - 6' Cord

The PP80006: 800 GPH High Lift Pump, Waterfalls/Ponds/Vertical Hydroponics/Aquaponics - 6' Cord Product Descrition 6 FOOT QUALITY CORD: Many pump manufacturers use an inferior quality cord, our highest quality (SJTW) Electric Cord is waterproof, 18# gauge copper wire, molded plug with ground, heavy duty flexible vinyl jacket, resists oil/grease/moisture, abrasion resistant and very good flexibility at all temperatures..PonicsPumps Sells 8 pump sizes. Click on "PonicPumps" below the main page title to see them all.

FLOW RATES: 792 Gallons Per Hour (GPH) @ 0' (Lift); 775 GPH @ 1'; 761 GPH @ 2'; 726 GPH @ 3'; 687 GPH @ 4'; 660 GPH @ 5'; 607 GPH @ 6'; 528 GPH @ 7'; 449 GPH @ 8'; 330 GPH @ 9'; 211 GPH @ 10'; 79 GPH @ 11'; Max Lift - 11' 6".

DIMENSIONS: 4.84" x 2.72" x 3.82"..OIL FREE, NO EXPOSED COPPER Safe for fish!

POLISHED ALUMINUM OXIDE CERAMIC IMPELLER SHAFT insures long pump life. This non-corrodible ceramic shaft is 3 times as hard as stainless steel.

NO SEAL TO FAIL! Uses wet-rotor design, so no seal to fail that would damage the pump motor.

LIMITED WARRANTY: 1 Year, only when sold by NicheNOVA..WATER-LUBRICATED HYDROGENATED NITRILE (HNBR) BEARINGS are used because they possess a very low coefficient of friction, have inherent vibration-dampening qualities and are non-polluting.

60 WATTS - 120VAC - 60Hz

3 OUTLET ADAPTORS : For 1/2", 5/8" and 3/4" tubing.

SALT OR FRESH WATER READY!

ADJUSTABLE INPUT FLOW RATE.EPOXY RESIN ENCASEMENT of key internal motor components prevents unwanted conductivity and corrosion of metal parts.

"SINTERED" NdFeB (RARE EARTH) MAGNETS. Our high-lift models use very expensive super-strength rare earth magnets so the pumps will efficiently produce high flow rates at lift extremes.

EASY CLEAN: No tools required to disassemble and clean filter/impeller...

HOW TO CHOOSE A HYDROPONIC, AQUAPONIC, ALGAPONIC, AQUARIUM, POND OR FOUNTAIN PUMP

First remember:
 - "Maximum Flow Rate" is meaningless because it is at ZERO lift.
 - "Maximum Head/Lift" is meaningless because the flow at that height is only a trickle.

You need to choose an affordable quality pump that produces the "desired flow at your required lift" at the lowest wattage.

Step 1: Determining Desired Flow Rate
Hydroponic Systems - typically flow through a single loop allowing a single pump and need a flow rate near 100 GPH for each grow bed loop up to 120 feet. Flood/drain beds - need 2 to 4 cycles per hour. Fish tanks - need a least one exchange per hour or extra oxygenation. Waterfalls - need 100 GPH for each inch of width.

Step 2: Calculating System Lift
Measure the "vertical distance" from the "top" of the water in the pump tank to the pump discharge point.

Step 3: Pump Selection Considerations
 - Continuous instead of intermittent pump duty cycle greatly increases pump life, plus no need for a timer or level control.
 - A rule of thumb is that an average pump will last 2-4 times the stated warranty period.
 - Best to buy a backup pump if fish or plants depend on the pump.

Step 4: Is A Foam Filter Needed?
A foam filter is not usually needed to protect the pump and the screen cover is enough. If your model has a foam filter and it clogs too fast, best to remove the filter.
 - If the screen clogs too fast... get a separate pre-filter, vortex filter or settling tank.
 - Micro-algae will not hurt a pump unless it stops water flow.
 - Most people buy our filter pumps for the longer 16 foot cord and discard the foam filter.

Discounts for PP80006: 800 GPH High Lift Pump, Waterfalls/Ponds/Vertical Hydroponics/Aquaponics - 6' Cord maybe will end soon. Need to hurry check this product hope you're lucky get limited discount for lowest and best price.

Feature PP80006: 800 GPH High Lift Pump, Waterfalls/Ponds/Vertical Hydroponics/Aquaponics - 6' Cord

6 FOOT QUALITY CORD: Many pump manufacturers use an inferior quality cord, our highest quality (SJTW) Electric Cord is waterproof, 18# gauge copper wire, molded plug with ground, heavy duty flexible vinyl jacket, resists oil/grease/moisture, abrasion resistant and very good flexibility at all temperatures.

PonicsPumps Sells 8 pump sizes. Click on "PonicPumps" below the main page title to see them all.

FLOW RATES: 792 Gallons Per Hour (GPH) @ 0' (Lift); 775 GPH @ 1'; 761 GPH @ 2'; 726 GPH @ 3'; 687 GPH @ 4'; 660 GPH @ 5'; 607 GPH @ 6'; 528 GPH @ 7'; 449 GPH @ 8'; 330 GPH @ 9'; 211 GPH @ 10'; 79 GPH @ 11'; Max Lift - 11' 6".

DIMENSIONS: 4.84" x 2.72" x 3.82".

OIL FREE, NO EXPOSED COPPER Safe for fish!

POLISHED ALUMINUM OXIDE CERAMIC IMPELLER SHAFT insures long pump life. This non-corrodible ceramic shaft is 3 times as hard as stainless steel.

NO SEAL TO FAIL! Uses wet-rotor design, so no seal to fail that would damage the pump motor.

LIMITED WARRANTY: 1 Year, only when sold by NicheNOVA.

WATER-LUBRICATED HYDROGENATED NITRILE (HNBR) BEARINGS are used because they possess a very low coefficient of friction, have inherent vibration-dampening qualities and are non-polluting.

60 WATTS - 120VAC - 60Hz

3 OUTLET ADAPTORS : For 1/2", 5/8" and 3/4" tubing.

SALT OR FRESH WATER READY!

ADJUSTABLE INPUT FLOW RATE

EPOXY RESIN ENCASEMENT of key internal motor components prevents unwanted conductivity and corrosion of metal parts.

"SINTERED" NdFeB (RARE EARTH) MAGNETS. Our high-lift models use very expensive super-strength rare earth magnets so the pumps will efficiently produce high flow rates at lift extremes.

EASY CLEAN: No tools required to disassemble and clean filter/impeller.

PP80006: 800 GPH High Lift Pump, Waterfalls/Ponds/Vertical Hydroponics/Aquaponics - 6' Cord

Admin rated 9 star rating from10 - 17points.